Skip to Content
To Overview

How Electric Vehicles Are Changing Our Power Grids

26. Forums des Automotive Clusters Rhein Main Neckar (von links): Richard Jordan (IHK Darmstadt), Michael Wißbach (CuroCon), Thomas Will (Landrat des Kreises Groß-Gerau), Volker Schier (ASAP Engineering GmbH) und Hans Peter Imhof (Kreisausschuss des Kreises Groß-Gerau)
Online zum Forum zugeschaltet: Prof. Dr.-Ing. Volker Pitz spricht am 26. Forum des Automotive Clusters Rhein Main Neckar über "Laden, steuern, zurückspeisen: Wie Elektrofahrzeuge unser Stromnetz verändern".

Prof. Dr.-Ing. Volker Pitz at the 26th Forum of the Rhine-Main-Neckar Automotive Cluster

More electric cars mean additional electricity demand. For the power grids, however, it’s not just a matter of how much electricity is consumed, but also when and where charging takes place. Flexible charging and bidirectional vehicles can help—but there are requirements for proper control. 

Prof. Dr.-Ing. Volker Pitz spoke on this topic at the 26th Forum of the Rhine-Main-Neckar Automotive Cluster, titled “From Vehicle to Energy Storage—Mobility Becomes Part of the Infrastructure.” The forum took place on November 17, 2026, at the CuroCon GmbH facilities in Zwingenberg.

 

Increased Electricity Demand—But Not Overnight

If all passenger cars and trucks in Germany were battery-electric, the additional electricity demand would amount to approximately 230 terawatt-hours (TWh) per year, according to current calculations. Including grid losses, the figure would be about 250 TWh. That would represent a significant increase compared to Germany’s gross electricity consumption of 527 TWh in 2025. A complete transition to electric vehicles would, however, take many years. 

This estimate projects approximately 800,000 newly registered battery electric vehicles (BEVs) for 2026. Together with new heat pumps and data centers, these developments could each result in approximately 2 TWh of additional electricity consumption—for a total of about 6 TWh.

This is offset in the 2026 estimate by approximately 20 GW of newly installed photovoltaic capacity and 10 GW of wind power capacity. This could result in approximately 36 TWh of additional electricity generation. These figures suggest that the additional annual consumption can be offset in the short term by the expansion of renewables. However, the key question remains whether electricity supply and demand will automatically balance out at every hour and in every location.

 

Power Capacity Is Key—and When Charging Takes Place

For grid design, it is not the annual energy requirement that matters, but rather the peak power flowing through the grid at any given moment. If many vehicles are charging simultaneously on the same street or at the same business location, the local load can increase significantly. Heat pumps and other consumers may also contribute to this.

Grid planning must therefore take local conditions into account: Where are the charging points and heat pumps located? When are they used? Where is electricity from photovoltaic systems fed into the grid? And at which grid level does the load occur?

 

How can bottlenecks be avoided?

If an overload is imminent, several measures can be considered:

  • Grid expansion: Reinforced or additional power lines can transmit more power, but they involve costs and construction work.
  • Load management: Charging processes are rescheduled or their power is temporarily reduced.
  • On-site storage: Storage systems can absorb or release electrical energy locally, thereby cushioning power peaks in the grid.

Flexible rates can shift electricity consumption to different times. However, a low market price does not automatically indicate whether the local grid currently has spare capacity. Market and grid signals serve different goals: Market-based control can shift consumption over time, but does not necessarily resolve a local grid congestion.

 

Storage systems can support both the market and the grid

Storage systems are often used to store electrical energy when plenty of renewable energy is available and prices are low. When generation is lower and electricity is more expensive, they release the stored energy. This can improve the timing alignment between generation and consumption.

Grid-friendly operation also requires the right location and appropriate control of the storage system. A storage system located near a high-generation site can absorb energy when grid overload is imminent. A storage system near a major consumption hub can release energy during periods of high load. In this way, storage systems can also help smooth out power flows in the grid. However, this requires them to be controlled differently depending on their location.

 

Bidirectional Charging: BEVs as Flexible Storage

With bidirectional charging, energy can flow not only into the vehicle battery but also back out of it. This means that electric cars could, in principle, serve as mobile storage units. A typical battery with a capacity of 70 kilowatt-hours would have an estimated “free” capacity of around 20 kWh (corresponding to about 30% of its total capacity), even if a portion remains reserved for mobility. The theoretical potential of the entire vehicle fleet is thus significant—but in practice, it depends on how many vehicles are actually connected and available, and how much power they can deliver.

The location of the vehicles is also important. For the power grid, it is crucial whether a vehicle is charging or feeding energy back into the grid in a region with high generation or in an area with high demand. The available battery capacity must therefore be managed to match the respective grid demand. Added to this are issues of compensation, battery usage, and the willingness of vehicle owners to make their batteries available for grid-supporting regulation.

 

V2H and V2G: Different Requirements

In Vehicle-to-Home (V2H), the vehicle supplies power to the owner’s home. The vehicle battery, PV system, and household consumption can be coordinated with one another. This can optimize self-consumption; reducing the load on the public grid is more of a side effect when energy fed into the grid and energy drawn from the grid are reduced.

In Vehicle-to-Grid (V2G), energy is fed back from the storage system into the public grid. This requires, among other things, regulations governing metering, billing, responsibilities, as well as compensation and grid fees. V2G offers more possibilities but requires correspondingly more coordination.

The regulatory framework is also evolving. On October 1, 2026, the Federal Network Agency adopted the MiSpeL regulation on the market integration of energy storage systems and charging points. Among other things, it is intended to facilitate the use of storage systems and bidirectional charging points. However, technical, economic, and organizational issues still need to be resolved for practical implementation. (bundesnetzagentur.de) The Electricity Tax Act also stipulates that the transfer of electricity from a vehicle battery to a charging point as part of bidirectional charging does not make the person in question a utility provider. (gesetze-im-internet.de)

 

Three Key Findings

  1. Grid benefit is a matter of power: The location and timing of consumption help determine where peak loads and bottlenecks occur.
  2. Flexibility helps when it’s tailored to local conditions: Load management and storage can smooth out power flows—but the control system must take the local grid situation into account.
  3. V2G requires coordinated processes: The technology opens up possibilities, but metering, billing, compensation, and responsibilities must also function properly.

Electric vehicles are not just additional consumers. When properly integrated, they can also provide flexibility for the power system. For this to happen, charging, storage, and grid operations must be coordinated both temporally and spatially.

[AI was used as an aid in drafting this text]